鋁合金卷簾門很常見，大家對它也都很熟悉。鋁合金卷簾門不僅型號齊全，能夠滿足人們不同的要求，而且優點也非常多，除了、耐用以外，占用空間小、靈活輕便、維護簡單等都是它的優點，因此，在大型廠房、、車庫等場所，人們都喜歡選用鋁合金卷簾門，下面，我們一起來了解怎樣安裝鋁合金卷簾門。

　　Aluminum alloy rolling shutter doors are very common and familiar to everyone. Aluminum alloy rolling shutter doors not only have a complete range of models to meet people's different requirements, but also have many advantages. In addition to safety and durability, their advantages include small space occupation, flexibility and portability, and simple maintenance. Therefore, in large factories, supermarkets, garages and other places, people like to choose aluminum alloy rolling shutter doors. Let's learn together how to install aluminum alloy rolling shutter doors.

　　1、核對洞口和卷簾門的規格

　　1. Check the specifications of the opening and rolling shutter door

　　這一項是正式安裝的準備工作，要確定洞口位置，核對洞口位置的準確性，確保洞口上面留足能夠容納卷簾門體的空間，其次，核對卷簾門的型號是不是正確，是不是與洞口規格相一致。

　　This is the preparation work for formal installation. Firstly, the position of the opening should be determined, and the accuracy of the opening position should be checked to ensure that there is enough space above the opening to accommodate the rolling shutter door. Secondly, the model of the rolling shutter door should be checked to ensure that it is correct and consistent with the specifications of the opening.

　　2、安裝導軌

　　2. Install the guide rail

　　，檢查導軌型號是否正確，接著，在洞口處定位、劃線、鉆孔，然后將導軌固定好，兩條導軌的安裝方法是相同的，但要注意保證它們在同一水平線上。

　　Firstly, check if the guide rail model is correct. Then, locate, mark, and drill holes at the opening, and fix the guide rail in place. The installation method for both guide rails is the same, but it is important to ensure that they are on the same horizontal line.

　　3、安裝左右支架

　　3. Install the left and right brackets

　　核對門洞尺寸，并以此為依據確定支架的具體安裝位置，接著，分別打孔，將左右支架固定，需要用水平儀調整兩個支架的水平度，確保它們水平。

　　Check the size of the door opening and use it as a basis to determine the specific installation position of the bracket. Then, drill holes separately to fix the left and right brackets. Finally, use a spirit level to adjust the levelness of the two brackets to ensure they are absolutely level.

　　4、將門體安裝到支架上

　　4. Install the door body onto the bracket

　　，根據門洞位置確定中軸長度，接著，將門體抬上支架，并用螺絲初步固定，然后，檢查門體與導軌和支架的銜接是否良好，如果沒有問題，就可以將螺絲擰緊，有問題就進行調試，直到問題解決。

　　Firstly, determine the length of the central axis based on the position of the door opening. Then, lift the door onto the bracket and preliminarily fix it with screws. Next, check whether the connection between the door body, guide rail, and bracket is good. If there are no problems, tighten the screws. If there are problems, adjust them until the problem is solved.

　　5、彈簧調試

　　5. Spring debugging

　　將彈簧按順時針方向扭轉，如果能扭轉一周，彈簧的暗轉就剛好合適，彈簧調試好以后，就可以揭開門體包裝，將其引入導軌。

　　Twist the spring clockwise. If it can be twisted once, the hidden rotation of the spring is just right. After adjusting the spring, you can open the door packaging and guide it into the guide rail.

　　6、卷門開關調試

　　6. Debugging of roll door switch

　　卷門安裝好以后，可以將卷門開關幾次，檢查它的運作是否正常，螺絲是否擰緊等問題，這時如果發現問題，就能及時解決，防止日后使用出現事故。

　　After the installation of the rolling door, it can be opened and closed several times to check whether its operation is normal and whether the screws are tightened. If any problems are found at this time, they can be solved in a timely manner to prevent safety accidents in future use.

　　7、安裝限位塊

　　7. Install limit block

　　限位塊一般安裝在門體底軌上面，且盡量安裝在底軌上的切口邊。

　　The limit block is generally installed on the bottom rail of the door body, and should be installed as much as possible on the cutting edge of the bottom rail.

　　8、安裝門鎖

　　8. Install door lock

　　要確定門鎖的安裝位置，將門體關上，插上鑰匙，扭動鑰匙使鎖管接觸到門體軌道的內側，這時做好記號，把門體打開。接著，在標記的位置鉆孔，安裝上門鎖，整個卷簾門就安裝好了。

　　First, determine the installation position of the door lock, close the door, insert the key, twist the key to make the lock tube touch the inside of the door track, mark it, and open the door. Next, drill holes at the marked positions, install the door lock, and the entire rolling shutter door is installed.

　　熟悉了鋁合金卷簾門的安裝程序，相信大家都看出來了，門洞位置的確定很關鍵，所以，我們在安裝卷簾門時一定要確保門洞的位置是正確的，這樣，整個卷簾門才能順利安裝上去。

　　Having familiarized ourselves with the installation procedure of aluminum alloy rolling shutter doors, I believe everyone can see that determining the position of the door opening is crucial. Therefore, when installing rolling shutter doors, we must ensure that the position of the door opening is correct, so that the entire rolling shutter door can be installed smoothly.

　　本文由  濟南卷簾門 友情奉獻.更多有關的知識請點擊  http://m.baozipinche.cn/   真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://m.baozipinche.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.